Remote Pilot Ace

Part 107 study guide

Part 107 airspace classes explained for drone pilots

Airspace is one of the biggest topics on the Part 107 knowledge test: the Airman Certification Standards give airspace and its requirements 15 to 25 percent of test items.

This guide explains each class in plain terms, how it looks on a sectional chart, and the rule that matters most for remote pilots: where you need permission from air traffic control before you fly.

Controlled and uncontrolled airspace

Controlled airspace is airspace of defined dimensions where air traffic control (ATC) provides service according to the airspace class. It covers Class A, B, C, D and E.

Uncontrolled airspace is Class G: the airspace that has not been designated as Class A, B, C, D or E.

Being in controlled airspace does not by itself mean you need permission. Part 107 requires prior ATC authorization in Class B, Class C and Class D airspace, and within the lateral boundaries of the surface area of Class E airspace designated for an airport.

Class A

Class A generally runs from 18,000 feet MSL up to and including FL 600. Unless otherwise authorized, everyone in it must fly under instrument flight rules (IFR), and visual charts do not depict it.

Part 107 flights stay far below it. A small drone may not fly higher than 400 feet above ground level, unless it stays within a 400-foot radius of a structure and no higher than 400 feet above the structure's top.

Class B

Class B surrounds the nation's busiest airports. It generally extends from the surface to 10,000 feet MSL, and each area is individually tailored, with a surface area and two or more layers, like an upside-down wedding cake.

A remote pilot must receive authorization from ATC before operating anywhere in Class B airspace.

Class C

Class C surrounds airports that have an operational control tower, are serviced by a radar approach control, and have a certain number of IFR operations or passenger enplanements. It generally extends from the surface to 4,000 feet above the airport elevation, charted in MSL.

A typical Class C has a 5 nautical mile radius core that starts at the surface, and a 10 nautical mile radius shelf that starts no lower than 1,200 feet and reaches 4,000 feet above the airport elevation. Remote pilots need authorization before operating in Class C.

Class D

Class D generally extends from the surface to 2,500 feet above the airport elevation, charted in MSL, around airports that have an operational control tower. A remote pilot must receive ATC authorization before operating in it.

Some Class D surface areas are part-time. When a Class D surface area is not in effect, the airspace may revert to a Class E surface area or to Class G, and the airport listing in the Chart Supplement states which.

Class E: surface areas and transition areas

Class E is the controlled airspace that is not Class A, B, C or D, and a large amount of the airspace over the United States is Class E. In most areas its base is 1,200 feet AGL; in many others it is the surface or 700 feet AGL.

For drone pilots, what matters is which kind of Class E you are in:

  • Surface area: Class E designated for an airport where a control tower is not in operation. It starts at the surface, and Part 107 requires prior ATC authorization within its lateral boundaries.
  • Surface area extension: Class E that begins at the surface and extends up to the overlying controlled airspace, built to contain instrument approach procedures. Arrival extensions become part of the surface area.
  • Transition area: Class E with a floor of 700 feet AGL or 1,200 feet AGL. It stays in effect continuously, regardless of airport operating hours.

Why the 700-foot floor is a common trap

The AIM warns not to confuse the 700-foot and 1,200-foot Class E transition areas with surface areas or surface area extensions. Below a transition area's floor the airspace is normally Class G, so a drone at or below 400 feet AGL there is normally outside Class E.

In most cases, a remote pilot will not need ATC authorization to operate in Class E airspace. The exception is the surface area designated for an airport.

Class G

Class G is uncontrolled airspace. It extends from the surface to the base of the overlying Class E airspace, and a remote pilot will not need ATC authorization to operate in it.

Other Part 107 rules still apply, including the 400-foot limit. You must not interfere with operations and traffic patterns at any airport, heliport or seaplane base.

Outside controlled airspace, no notification or authorization is needed to fly near an airport, but you must avoid all traffic patterns and approach corridors.

How each class looks on a sectional chart

Sectional charts show Class B, C, D and E airspace with colors, line styles and altitude labels:

  • Class A: not depicted on visual charts.
  • Class B: each sector's ceiling and floor are printed in solid blue figures, in MSL with the last two zeros omitted. A floor marked with a plus sign means the floor starts above that altitude.
  • Class C: ceiling and floor figures are printed in solid magenta. A ceiling of T means up to, but not including, the floor of the Class B above.
  • Class D: a blue dashed line. A minus sign in front of the ceiling figure means from the surface to, but not including, that altitude.
  • Class E surface area: a magenta dashed line.
  • Class E starting at 700 feet AGL: a magenta vignette. Floors other than 700 feet that border Class G: a blue vignette.

Reading Class E floors on the chart

Class E exists at 1,200 feet AGL unless designated otherwise. So where no vignette or dashed line appears, Class G usually runs from the surface up to 1,200 feet AGL.

Special use airspace

Special use airspace is where certain activities must be confined, or where limits may be placed on aircraft that are not part of those activities. Except for controlled firing areas, it is shown on visual charts. The main types are:

  • Prohibited areas (P followed by a number): flight is prohibited, for security or other reasons associated with the national welfare.
  • Restricted areas (R followed by a number): flight is not wholly prohibited but is subject to restrictions, often because of invisible hazards such as artillery firing or guided missiles.
  • Warning areas (W followed by a number): airspace extending from 3 nautical miles outward from the U.S. coast with activity that may be hazardous to nonparticipating aircraft.
  • Military operations areas (MOAs): airspace that separates certain military training activities from IFR traffic. They are named rather than numbered.
  • Alert areas (A followed by a number): areas that may contain a high volume of pilot training or an unusual type of aerial activity. Everyone flying in them is equally responsible for collision avoidance.
  • Controlled firing areas (CFAs): not charted, because their activities are suspended when an aircraft might be approaching the area.

Prohibited and restricted areas, and TFRs

Under Part 107, you may not fly a small drone in a prohibited or restricted area unless you have permission from the using or controlling agency, as appropriate.

A temporary flight restriction (TFR) is a type of NOTAM. It defines an area where air travel is restricted because of a hazardous condition, a special event or a general warning. Part 107 requires you to follow the TFR rules in 14 CFR 91.137 through 91.145 and 99.7.

Only TFRs relating to national security are charted, so check NOTAMs before each flight. The FAA website www.tfr.faa.gov is one way to verify that there is no TFR in your area.

How to get airspace authorization

Part 107 pilots can request airspace authorizations through LAANC (Low Altitude Authorization and Notification Capability) or DroneZone to fly in Class B, Class C, Class D or within the lateral boundaries of the surface area of Class E airspace designated for an airport.

Requests are based on UAS Facility Maps (UASFM). The map values show the maximum altitude at which an operation can be authorized without further coordination with the ATC facility. LAANC gives near real-time authorization within those altitudes, and you can request further coordination to fly above them, up to 400 feet AGL.

A request can be denied based on traffic density, controller workload, communication issues or anything else that could affect the safe flow of air traffic. Information on the current process is at faa.gov/uas.

Before every flight, Part 107 also requires you to assess the local airspace and any flight restrictions.

Frequently asked questions

Do I need ATC authorization to fly in Class E airspace?

Only within the lateral boundaries of a Class E surface area designated for an airport. In most other Class E airspace, a remote pilot will not need ATC authorization.

Can I fly under a magenta vignette without authorization?

Usually yes. The magenta vignette marks Class E that starts at 700 feet AGL, and below that floor the airspace is normally Class G, where no ATC authorization is needed.

Is Class A airspace shown on a sectional chart?

No. Class A generally starts at 18,000 feet MSL, and visual charts do not depict it.

What does a blue dashed line mean?

It marks Class D airspace around an airport with an operational control tower. You must receive ATC authorization before flying inside it.

Can I fly a drone in a restricted area?

Only with permission from the using or controlling agency, as appropriate.

Are TFRs printed on sectional charts?

Only TFRs relating to national security are charted. A TFR is a type of NOTAM, so check NOTAMs before each flight.

Sources

Every fact in this guide is taken from these FAA publications. Check the current edition before your test.

Practice what you just read: free Part 107 practice test.

Practice the full question bank in the app

Remote Pilot Ace has topic practice, full 65-question mock exams in the test format, zoomable figures and an explanation with its source for every answer. Free to start.

Download on the App Store